Royal Vendors' High Visibility Vender (HVV, models 780-12, 768-12, 654-12, 650-12) Operation and Service Manual Download PDF: HVV manual … [Read more...]
370. Main Door Stop Kit Installation
February 19, 2013 by ·
SUBJECT: Main Door Stop Kit Installation REVISION: 00 MODELS: All conventional venders with rocker-type door switch PURPOSE: This bulletin describes the procedure for installing the main door stop kit, which is designed to secure the vender's door to keep it from swinging farther out than desired. Download PDF: Service Bulletin 370 … [Read more...]
54. External DEX Harness Installation in HVV
November 15, 2011 by ·
Subject: External DEX Harness Installation in HVV Revision: 00 Models: Royal HVV Tools required: Drill with 7/16" (11 mm) bit (only needed if no DEX port hole present) Estimated time: … [Read more...]
113. Lamp Relay Kit Installation
October 24, 2011 by ·
SUBJECT: Lamp Relay Kit Installation REVISION: 09 MODELS: GIII, Merlin III, Merlin IV, HVV, and TDV venders PURPOSE: This bulletin shows the correct procedure for installing the lamp relay kit, which allows the controller to turn the lighting system on or off. Download PDF: Service Bulletin 113 … [Read more...]
336. RDP Antenna Placement
November 8, 2010 by ·
SUBJECT: RDP Antenna Placement REVISION: 00 MODELS: All models PURPOSE: When installing an RDP unit in venders, it is imperative that the unit's antennas be placed correctly. Failure to do so can cause signal interference with several other components of the vender, including the chute sensor. This bulletin describes the correct placement of these antennas. Download PDF: Service Bulletin … [Read more...]
329. Piezoresistive Chute Sensor Installation
August 11, 2010 by ·
SUBJECT: Piezoresistive Chute Sensor Installation REVISION: 00 MODELS: All conventional venders PURPOSE: Beginning with vender serial number 201030BA00001, the older-style chute sensor has been replaced by a piezoresistive sensor. This bulletin explains the procedure for installing the newer sensor in place of the original-style sensor. Download PDF: Service Bulletin 329 … [Read more...]
321. New Controller Service Mode Button
May 6, 2010 by ·
SUBJECT: New Controller Service Mode Button REVISION: 00 MODELS: All current-production venders PURPOSE: The service mode buttons on the Coinco controllers have changed. Previously, from 2002 (KO controllers) or the mid-1990s (all other venders) until early 2010, the service mode button was a blue, round disk. The newer controllers have a blue or tan cylinder-style button. The function of … [Read more...]
315. Energy Star® Tier 2 Temperature Sensor Conversion Kit Installation
February 17, 2010 by ·
SUBJECT: Energy Star® Tier 2 Temperature Sensor Conversion Kit Installation REVISION: 01 MODELS: All conventional venders PURPOSE: This bulletin describes the process for converting older non-Energy Star or Energy Star Tier 1 venders to the newer Energy Star Tier 2 standard for refrigeration control. Download PDF: Service Bulletin 315 … [Read more...]
44. Coinco Bill Recycler Validator Installation
January 11, 2010 by ·
Subject: Coinco Bill Recycler Validator Installation Revision: 00 Models: GIII, HVV, RVV 500 Tools required: N/A Estimated time: N/A Purpose: New controller software has been released that allows Coinco bill-recycling validators to be connected directly to the controller's MDB harness without the need for a controller adapter box, which is required with older software. This Helpful Hint … [Read more...]
301. Defective GFCI Harnesses
March 5, 2009 by ·
SUBJECT: Defective GFCI Harnesses REVISION: 00 MODELS: All models IMPORTANT INFORMATION: Royal Vendors, Inc., has recently identified some defective Ground Fault Circuit Interruptor (GFCI) power cords manufactured by Leviton Manufacturing Co., Inc. Approximately 10% of venders manufactured by Royal Vendors from late January 2009 through the first week of March 2009 may have these faulty … [Read more...]
