SUBJECT: Software Update to Correct GIII KO Chute Sensor Function REVISION: 00 MODELS: All GIII models with KO control boards PURPOSE: Royal Vendors has recently found that some customers with equipment built from mid-2007 to mid-2008 had chute sensors that would not properly adjust, causing double vending of bottles. In most cases, replacing the chute sensor seems to remedy this problem, … [Read more...]
Archive: Documentation
247. Quick Release Main Wiring Harness Kit Installation
July 16, 2008 by ·
SUBJECT: Quick Release Main Wiring Harness Kit Installation REVISION: 02 MODELS: Most Royal Vendors, Dixie-Narco, and Vendo models (115 VAC) PURPOSE: The Quick Release Main Wiring Harness Kits are designed to replace several different Royal Vendors, Dixie-Narco, and Vendo OEM main wiring harnesses. Four kits are available for replacing the original main wiring harnesses. The Universal kit … [Read more...]
7. Installation of a New Vend Chain
July 15, 2008 by ·
Subject: Installation of a New Vend Chain Revision: 03 Models: GIII venders Tools required: Long wire tie, Phillips screwdriver Estimated time: 5 minutes Purpose: This document describes the process for installing a new vend chain in GIII venders. Download PDF: Helpful Hint 7 … [Read more...]
294. Cup Floor Breakage on RVV 500
July 8, 2008 by ·
SUBJECT: Cup Floor Breakage on RVV 500 REVISION: 00 MODELS: RVV NG 500 PURPOSE: Due to a moulded component issue, a limited amount of RVV NG 500 product cup floors may have breakage. Royal Vendors, Inc., and Coin Acceptors, Inc., have identified the cause, and the moulding process has been modified to prevent this breakage from occuring in the future. This issue is believed to pertain to a … [Read more...]
295. Intermittent Fuse Assembly Failure on RVV 500
July 8, 2008 by ·
SUBJECT: Intermittent Fuse Assembly Failure on RVV 500 REVISION: 00 MODELS: RVV NG 500 PURPOSE: Due to a faulty spring in the bayonet-style fuse assembly, a limited amount of RVV NG 500 venders may experience intermittent power failures. This spring has been modified to prevent this type of failure from occuring in the future. This issue is believed to pertain to a small number of venders … [Read more...]
43. Enabling / Disabling Timers
June 9, 2008 by ·
Subject: Enabling / Disabling Timers Revision: 00 Models: Merlin IV, GIII, RVV NG Tools required: None Estimated time: <1 minutes Purpose: This Helpful Hint describes how to quickly disable timers and quickly enable them again without changing the programmed start and stop times. Download PDF: Helpful Hint 43 … [Read more...]
293. Installation of the RVV 500 Coin Chute Support Kit
May 30, 2008 by ·
SUBJECT: Installation of the RVV 500 Coin Chute Support Kit REVISION: 00 MODELS: RVV NG 500 PURPOSE: The Coin Chute Support Assembly was designed to prevent vandalism to the coin chute on the RVV NG 500 model vender. This bulletin describes the procedure for installing this kit. Download PDF: Service Bulletin 293 … [Read more...]
292. Installation of the RVV IEC Ballast Assembly
May 13, 2008 by ·
SUBJECT: Installation of the RVV IEC Ballast Assembly REVISION: 00 MODELS: RVV NG (230 VAC models) PURPOSE: The seven-connector 220-240 volt electronic ballast that was originally used in the international RVV NGs has been replaced by a four-connector electronic ballast. The assembly for this new ballast is shipped from Royal Vendors in two distinct sections: the lamp harnessing (including … [Read more...]
129. 20 oz. Dasani Plus bottle
May 5, 2008 by ·
Product name: 20 oz. Dasani Plus bottle Bottler / company: The Coca-Cola Company Volume: 20 oz. / 591 mL Package type: PET Height: 9.17 in. / 233 mm Diameter: 2.61 in. / 66.4 mm Weight: 1.35 lbs. / 0.61 kg Country of origin: USA Venders: GIII, TDV, RVV NG Download PDF: PVS 129 … [Read more...]
289. Installation of the External Hole Cover Plate Kit
March 3, 2008 by ·
SUBJECT: Installation of the External Hole Cover Plate Kit REVISION: 00 MODELS: Mt Franklin RVV NG 500 venders (Australian models only) PURPOSE: Some Mt Franklin RVV NG 500 venders built in early 2008 had an incorrectly placed mounting hole for the Harvest system aerial. A carriage bolt was installed in the incorrect hole as a temporary measure. A kit was designed to replace the carriage … [Read more...]
