SUBJECT: Universal Caster Kit Installation REVISION: 02 MODELS: All venders (not coolers) PURPOSE: This bulletin explains the procedure for installing the Universal Caster Kit on all vender models. Download PDF: Service Bulletin 234 … [Read more...]
Archive: Documentation
288. North American Daylight Saving Time Update
October 8, 2007 by ·
SUBJECT: North American Daylight Saving Time Update REVISION: 00 MODELS: MOST (see bulletin) PURPOSE: Effective the 1st of July, 2007, all Royal Vendors controllers in current production are compliant with the new regulations concerning Daylight Saving Time (DST) in North America. This bulletin describes the correct procedure for updating certain controllers which are already in the market … [Read more...]
286. RVV 500 Refrigeration Issue
August 15, 2007 by ·
SUBJECT: RVV 500 Refrigeration Issue REVISION: 00 MODELS: RVV 500 PURPOSE: In the last several months, Royal Vendors has seen an increase in refrigeration-related failures on the RVV 500. Royal Vendors has identified the issue to be related to the expansion valve. Failure of this valve to function properly can cause the software to shut down the refrigeration system due to insufficient … [Read more...]
41. RVV NG Illustrated Troubleshooting Guide
April 24, 2007 by ·
Subject: RVV NG Illustrated Troubleshooting Guide Revision: 01 Models: RVV NG Tools required: N/A Estimated time: N/A Purpose: This Helpful Hint is designed to aid in the step-by-step troubleshooting of the RVV NG. Download PDF: Helpful Hint 41 … [Read more...]
284. 20+ Vend Motors
April 20, 2007 by ·
SUBJECT: T12 to Low-power LED Conversion Kit Installation REVISION: 00 MODELS: All 20+ (TDV) venders PURPOSE: 20+ (TDV) Venders have two different vend motors installed: a low-torque motor, for all front columns; and a high-torque motor, for all rear columns. These two motor types are NOT interchangeable. Download PDF: Service Bulletin 284 … [Read more...]
282. RVV NG Changer Guard Kit Installation
March 14, 2007 by ·
SUBJECT: RVV NG Changer Guard Kit Installation REVISION: 00 MODELS: RVV NG with T-handle Lock PURPOSE: This bulletin describes the proper procedure for installing the Changer Guard Kit, which provides protection from vandalism for the changer in the RVV NG. Download PDF: Service Bulletin 282 … [Read more...]
283. GFCI Main Wiring Harness Implementation
March 13, 2007 by ·
SUBJECT: GFCI Main Wiring Harness Implementation REVISION: 00 MODELS: All venders built for use in the USA (including Puerto Rico) and Canada PURPOSE: Effective April 2007, all new venders are required to have a GFCI (Ground Fault Circuit Interrupter) built into the main wiring harness coming from the power source (wall outlet). This change has been legally mandated by Underwriters … [Read more...]
42. 220-240 VAC Electronic Ballast Replacement
January 30, 2007 by ·
Subject: 220-240 VAC Electronic Ballast Replacement Revision: 00 Models: RVV NG, Merlin RB (230 VAC 50 Hz models only) Tools required: Phillips screwdriver Estimated time: 5 minutes Purpose: The seven-connector 220-240 volt electronic ballast that was originally used in the international RVV NG and Merlin RB venders has been replaced by a newer four-connector electronic ballast. This … [Read more...]
271. Merlin RB Lock Cover Kit Installation
January 16, 2007 by ·
SUBJECT: Merlin RB Lock Cover Kit Installation REVISION: 01 MODELS: Merlin RB PURPOSE: This bulletin describes the correct procedure for installing the Merlin RB Lock Cover Kit, which prevents vandals from drilling into the T-handle lock cylinder. Download PDF: Service Bulletin 271 … [Read more...]
249. Installation of the RVV Lock Cover Kit
January 16, 2007 by ·
SUBJECT: Installation of the RVV Lock Cover Kit REVISION: 02 MODELS: RVV, RVV NG, RVV Gen II PURPOSE: Installing a lock cover helps to prevent vandalism and deter theft. This bulletin describes the proper procedure for installing a lock cover kit on the RVV and the RVV NG. Download PDF: Service Bulletin 249 … [Read more...]
