Subject: Recommendations to Enhance Package Vending Reliability Revision: 01 Models: 804, 660, 550 Tools required: N/A Estimated time: N/A Purpose: Bottle bridging can have various causes. This Helpful Hint bulletin describes how to enhance vending reliability in a GIII-style machine. Download PDF: Helpful Hint 48 … [Read more...]
Archive: Helpful Hints
47. CCIV Interconnections
Subject: CCIV Interconnections Revision: 02 Models: CCIV Tools required: N/A Estimated time: N/A Purpose: This bulletin shows the harness / cable connections between the computer, monitor, and PayLink device. It also includes part numbers and color codes for the cables and harnesses. (Each cable or harness has a colored label wrapped around one end, except black.) Download … [Read more...]
8. Revised Serial Number Format
Subject: Revised Serial Number Format Revision: 05 Models: All venders produced after 1 October 1999 Tools required: N/A Estimated time: N/A Information: Royal Vendors issued a revised serial numbering system effective 1 October 1999. Download PDF: Helpful Hint 8 … [Read more...]
46. Disabling Lighting Through The Service Menu
Subject: Disabling Lighting Through The Service Menu Revision: 00 Models: All KO models Tools required: None Estimated time: <5 minutes Purpose: This Helpful Hint bulletin describes the recommended procedure for turning off the vender's lighting through the internal programming to conserve energy, instead of disconnecting circuits or removing bulbs. Download PDF: Helpful Hint 46 … [Read more...]
45. TDV Vending Reliability Checks
Subject: TDV Vending Reliability Checks Revision: 00 Models: TDV Tools required: Small flat screwdriver Estimated time: <5 minutes Purpose: Ensuring that all programming is set correctly and the optic sensors are properly adjusted is critical to the reliability of the Triple Depth Vender's operation. This Helpful Hint bulletin explains how to ensure these components are adjusted … [Read more...]
44. Coinco Bill Recycler Validator Installation
Subject: Coinco Bill Recycler Validator Installation Revision: 00 Models: GIII, HVV, RVV 500 Tools required: N/A Estimated time: N/A Purpose: New controller software has been released that allows Coinco bill-recycling validators to be connected directly to the controller's MDB harness without the need for a controller adapter box, which is required with older software. This Helpful Hint … [Read more...]
7. Installation of a New Vend Chain
Subject: Installation of a New Vend Chain Revision: 03 Models: GIII venders Tools required: Long wire tie, Phillips screwdriver Estimated time: 5 minutes Purpose: This document describes the process for installing a new vend chain in GIII venders. Download PDF: Helpful Hint 7 … [Read more...]
43. Enabling / Disabling Timers
Subject: Enabling / Disabling Timers Revision: 00 Models: Merlin IV, GIII, RVV NG Tools required: None Estimated time: <1 minutes Purpose: This Helpful Hint describes how to quickly disable timers and quickly enable them again without changing the programmed start and stop times. Download PDF: Helpful Hint 43 … [Read more...]
41. RVV NG Illustrated Troubleshooting Guide
Subject: RVV NG Illustrated Troubleshooting Guide Revision: 01 Models: RVV NG Tools required: N/A Estimated time: N/A Purpose: This Helpful Hint is designed to aid in the step-by-step troubleshooting of the RVV NG. Download PDF: Helpful Hint 41 … [Read more...]
42. 220-240 VAC Electronic Ballast Replacement
Subject: 220-240 VAC Electronic Ballast Replacement Revision: 00 Models: RVV NG, Merlin RB (230 VAC 50 Hz models only) Tools required: Phillips screwdriver Estimated time: 5 minutes Purpose: The seven-connector 220-240 volt electronic ballast that was originally used in the international RVV NG and Merlin RB venders has been replaced by a newer four-connector electronic ballast. This … [Read more...]
