Subject: RVV NG Test Diagnostics Revision: 00 Models: RVV NG Tools required: None Estimated time: Variable Purpose: The Test Diagnostics routines in the RVV NG venders are important tools for ensuring vending reliability and function. This Helpful Hint describes, step-by-step, all of the routines included in the Test Diagnostics menu. NOTE: Only software revisions 67241-4 and higher and … [Read more...]
Archive: Helpful Hints
39. Correct Shelf Quantity Setting
Subject: Correct Shelf Quantity Setting Revision: 00 Models: RVV NG Tools required: None Estimated time: <1 minutes Purpose: On all RVV NG’s with -4 or higher software, after entering the Calibration menu, the first item displayed is “Shelf.” This submenu item should always be set to “05,” but generally it should never be entered into. This Helpful Hint describes the correct procedure … [Read more...]
38. Disabling Milk Merchandiser Health Sensor
Subject: Disabling Milk Merchandiser Health Sensor Revision: 00 Models: Milk Merchandisers Tools required: None Estimated time: <1 minutes Purpose: The Milk Merchandiser’s health sensor is not required for aseptic products. This Helpful Hint describes the procedure for disabling this health sensor. NOTE: The health sensor cannot be disabled on control boards with EEPROM revision … [Read more...]
37. Column Jam Clearing in HVV and TDV
Subject: Column Jam Clearing in HVV and TDV Revision: 00 Models: All High Visibility Venders (HVV) and all Triple-Depth Venders (TDV) Tools required: None Estimated time: <5 minutes Purpose: Column jam errors registered by the control board on HVV and TDV models are not self-clearing. Because of this, once the problem has been corrected, those columns will not vend again until the … [Read more...]
36. Selection Depth Setting in TDV
Subject: Selection Depth Setting in TDV Revision: 00 Models: All Triple-Depth Venders (TDV) Tools required: None Estimated time: <5 minutes Purpose: In TDV programming, selection depth settings (SdEP) will always revert to “1” (single depth) for all selections which only have front columns assigned to them. If space-to-sales settings are ever changed for any reason, it is imperative … [Read more...]
35. Chute Sensor Adjustment on International KO Control Board
Subject: Chute Sensor Adjustment on International KO Control Board Revision: 00 Models: GIII with 836152 KO Control Board (non-USA [including Puerto Rico] and Canada) Tools required: Flat screwdriver Estimated time: <15 minutes Purpose: This Helpful Hint describes how to properly adjust the chute sensor on the 836152 KO Control Board and to eliminate chute sensors with insufficient … [Read more...]
33. Royal Vision Vender: For Superior Performance… (RVV 400)
Subject: Royal Vision Vender: For Superior Performance... Revision: 01 Models: RVV 400 Tools required: N/A Estimated time: N/A Purpose: Proper setup and maintenance of the Royal Vision Vender is critical to its efficiency and ability to function. This bulletin describes the most critical maintenance points for the Royal Vision Vender. Download PDF: Helpful Hint 33 … [Read more...]
34. Using the Cell Setup Gauge (RVV model 400 only)
Subject: Using the Cell Setup Gauge Revision: 00 Models: RVV 400 Tools required: Cell Setup Gauge Estimated time: <1 minute Purpose: The RVV Cell Setup Gauge (part number 815581) is a flat piece of clear plastic used to determine the proper spacing between the RVV outside cell wall and the products loaded in the cell. Download PDF: Helpful Hint 34 … [Read more...]
32. Proper Depth Setting on Milk Venders
Subject: Proper Depth Setting on Milk Venders Revision: 00 Models: Milk Merchandiser Tools required: None Estimated time: <1 minute Purpose: Proper depth setting on Milk venders is essential, especially for selections vending bottles from rear columns. When set incorrectly, the vend motors in rear columns may not turn far enough for the bottle to drop from the column, resulting in a … [Read more...]
28. Installation of the Multi-Layer Control Board
Subject: Installation of the Multi-Layer Control Board Revision: 02 Models: Merlin IV, Merlin 20+, Milk Merchandiser, EZ Vender Tools required: None Estimated time: 10 minutes Purpose: Beginning in mid-December 2001, all new Merlin venders have a Multi-Layer Control Board, instead of the older single-layer board. The design of this new board provides better protection against … [Read more...]
