SUBJECT: 1.0 kVA Transformer Kit Installation REVISION: 00 MODELS: GIII, Merlin IV, RVV NG PURPOSE: This bulletin describes the proper procedure for installing the 1.0 kVA transformer in a standard 115 VAC 60 Hz vender to convert it for use in a 230 VAC 60 Hz location. Download PDF: Service Bulletin 296 … [Read more...]
247. Quick Release Main Wiring Harness Kit Installation
July 16, 2008 by ·
SUBJECT: Quick Release Main Wiring Harness Kit Installation REVISION: 02 MODELS: Most Royal Vendors, Dixie-Narco, and Vendo models (115 VAC) PURPOSE: The Quick Release Main Wiring Harness Kits are designed to replace several different Royal Vendors, Dixie-Narco, and Vendo OEM main wiring harnesses. Four kits are available for replacing the original main wiring harnesses. The Universal kit … [Read more...]
7. Installation of a New Vend Chain
July 15, 2008 by ·
Subject: Installation of a New Vend Chain Revision: 03 Models: GIII venders Tools required: Long wire tie, Phillips screwdriver Estimated time: 5 minutes Purpose: This document describes the process for installing a new vend chain in GIII venders. Download PDF: Helpful Hint 7 … [Read more...]
43. Enabling / Disabling Timers
June 9, 2008 by ·
Subject: Enabling / Disabling Timers Revision: 00 Models: Merlin IV, GIII, RVV NG Tools required: None Estimated time: <1 minutes Purpose: This Helpful Hint describes how to quickly disable timers and quickly enable them again without changing the programmed start and stop times. Download PDF: Helpful Hint 43 … [Read more...]
234. Universal Caster Kit Installation
January 11, 2008 by ·
SUBJECT: Universal Caster Kit Installation REVISION: 02 MODELS: All venders (not coolers) PURPOSE: This bulletin explains the procedure for installing the Universal Caster Kit on all vender models. Download PDF: Service Bulletin 234 … [Read more...]
267. Refrigeration Issues Caused By Control Board Battery Replacement
November 16, 2005 by ·
SUBJECT: Refrigeration Issues Caused By Control Board Battery Replacement REVISION: 00 MODELS: All Venders with Electronic Refrigeration PURPOSE: Replacing a control board battery could affect the calibration of the vender’s temperature sensor, causing evaporator freeze-ups or warm product. This bulletin explains the corrective procedure for this issue. Download PDF: Service Bulletin 267 … [Read more...]
260. Faulty Magnets in GIII Vend Chains
November 19, 2004 by ·
SUBJECT: Faulty Magnets in GIII Vend Chains REVISION: 00 MODELS: GIII PURPOSE: Some GIII vend chains produced for service parts were found in the field to have faulty magnets. NOTE: This bulletin only concerns vend chains produced for service parts, not the original chains installed in the venders at the factory. Download PDF: Service Bulletin 260 … [Read more...]
147. Chain Guard Installation
April 4, 2003 by ·
SUBJECT: Chain Guard Installation REVISION: 05 MODELS: GIII PURPOSE: To prevent vandalism / product theft by hooking on chain or release levers. Download PDF: Service Bulletin 147 … [Read more...]
18. Ground Strap for the Inner Door
June 18, 2002 by ·
Subject: Ground Strap for the Inner Door Revision: 03 Models: All Venders Tools required: Phillips screwdriver, drill, 1/8” drill bit Estimated time: 1 minute Purpose: For instructions on installing a ground strap to the inner door. Download PDF: Helpful Hint 18 … [Read more...]
6. Preventive Maintenance for Ballast Assembly
June 18, 2002 by ·
Subject: Preventive Maintenance for Ballast Assembly Revision: 03 Models: All Venders with Ballast Assembly Tools required: None Estimated time: 10 minutes Purpose: To obtain maximum efficiency of the ballast. Download PDF: Helpful Hint 6 … [Read more...]
