Subject: Disabling Milk Merchandiser Health Sensor Revision: 00 Models: Milk Merchandisers Tools required: None Estimated time: <1 minutes Purpose: The Milk Merchandiser’s health sensor is not required for aseptic products. This Helpful Hint describes the procedure for disabling this health sensor. NOTE: The health sensor cannot be disabled on control boards with EEPROM revision … [Read more...]
Archive: Documentation
274. Installation of the RVV NG Milk Conversion Kit
June 5, 2006 by ·
SUBJECT: Installation of the RVV NG Milk Conversion Kit REVISION: 00 MODELS: RVV NG PURPOSE: Before loading perishable items in the RVV Next Generation vender (RVV NG), a health safety sensor must be installed and enabled. This bulletin describes the proper procedure for installing the RVV NG Milk Conversion Kit, which includes this health safety sensor. Download PDF: Service Bulletin 274 … [Read more...]
37. Column Jam Clearing in HVV and TDV
May 2, 2006 by ·
Subject: Column Jam Clearing in HVV and TDV Revision: 00 Models: All High Visibility Venders (HVV) and all Triple-Depth Venders (TDV) Tools required: None Estimated time: <5 minutes Purpose: Column jam errors registered by the control board on HVV and TDV models are not self-clearing. Because of this, once the problem has been corrected, those columns will not vend again until the … [Read more...]
36. Selection Depth Setting in TDV
April 12, 2006 by ·
Subject: Selection Depth Setting in TDV Revision: 00 Models: All Triple-Depth Venders (TDV) Tools required: None Estimated time: <5 minutes Purpose: In TDV programming, selection depth settings (SdEP) will always revert to “1” (single depth) for all selections which only have front columns assigned to them. If space-to-sales settings are ever changed for any reason, it is imperative … [Read more...]
272. Override Switch Kit for RVV NG
March 30, 2006 by ·
SUBJECT: Override Switch Kit for RVV NG REVISION: 01 MODELS: RVV NG PURPOSE: This bulletin explains the procedure for installing an override key switch kit in the RVV NG. Download PDF: Service Bulletin 272 … [Read more...]
273. Installation of the RVV NG Validator Security Door
March 27, 2006 by ·
SUBJECT: Installation of the RVV NG Validator Security Door REVISION: 00 MODELS: RVV NG PURPOSE: This bulletin explains the procedure for installing the validator security door kit in the RVV NG. Download PDF: Service Bulletin 273 … [Read more...]
270. Port Latch Replacement
January 20, 2006 by ·
SUBJECT: Port Latch Replacement REVISION: 00 MODELS: RVV NG PURPOSE: Some RVV NG port latches may have burrs on them that prevent them from sliding efficiently, allowing the port door to become stuck in the open position. This bulletin describes the proper procedure for replacing the port latch. Download PDF: Service Bulletin 270 … [Read more...]
267. Refrigeration Issues Caused By Control Board Battery Replacement
November 16, 2005 by ·
SUBJECT: Refrigeration Issues Caused By Control Board Battery Replacement REVISION: 00 MODELS: All Venders with Electronic Refrigeration PURPOSE: Replacing a control board battery could affect the calibration of the vender’s temperature sensor, causing evaporator freeze-ups or warm product. This bulletin explains the corrective procedure for this issue. Download PDF: Service Bulletin 267 … [Read more...]
35. Chute Sensor Adjustment on International KO Control Board
November 15, 2005 by ·
Subject: Chute Sensor Adjustment on International KO Control Board Revision: 00 Models: GIII with 836152 KO Control Board (non-USA [including Puerto Rico] and Canada) Tools required: Flat screwdriver Estimated time: <15 minutes Purpose: This Helpful Hint describes how to properly adjust the chute sensor on the 836152 KO Control Board and to eliminate chute sensors with insufficient … [Read more...]
265. Installation of the RVV Inner Door Seal Kit
August 30, 2005 by ·
SUBJECT: Installation of the RVV Inner Door Seal Kit REVISION: 00 MODELS: RVV PURPOSE: Some Royal Vision Venders (RVV) may have air leaks which will cause freezing in and around the evaporator area. This bulletin describes the proper procedure for sealing these areas. Download PDF: Service Bulletin 265 … [Read more...]
