SUBJECT: Column Conversion to Accomodate 12 oz Cans in Merlin RB REVISION: 00 MODELS: Merlin RB PURPOSE: This bulletin explains the procedure for converting column 4 in the Merlin RB vender to accomodate 12 oz (355 mL) cans. NOTE: This bulletin applies only to column 4. Columns 1-3 are more narrow and cannot accomodate the 12 oz cans. Download PDF: Service Bulletin 353 … [Read more...]
Archive: Documentation
55. External DEX Harness Installation in RVV 500
November 16, 2011 by ·
Subject: External DEX Harness Installation in RVV 500 Revision: 00 Models: RVV 500 Tools required: None Estimated time: … [Read more...]
54. External DEX Harness Installation in HVV
November 15, 2011 by ·
Subject: External DEX Harness Installation in HVV Revision: 00 Models: Royal HVV Tools required: Drill with 7/16" (11 mm) bit (only needed if no DEX port hole present) Estimated time: … [Read more...]
351. Evaporator Fan Motor Grille Spacer Installation in RVV 500
November 15, 2011 by ·
SUBJECT: Evaporator Fan Motor Grille Spacer Installation in RVV 500 REVISION: 01 MODELS: RVV 500 (115 VAC models only) BACKGROUND INFORMATION: The energy-efficient evaporator fan motor has been redesigned for improved moisture resistance. As a result, the fan assembly is now slightly thicker, requiring the replacement of the original grille spacers with longer ones in RVV 500s built prior to … [Read more...]
113. Lamp Relay Kit Installation
October 24, 2011 by ·
SUBJECT: Lamp Relay Kit Installation REVISION: 09 MODELS: GIII, Merlin III, Merlin IV, HVV, and TDV venders PURPOSE: This bulletin shows the correct procedure for installing the lamp relay kit, which allows the controller to turn the lighting system on or off. Download PDF: Service Bulletin 113 … [Read more...]
51. Cooler Door Replacement
October 20, 2011 by ·
Subject: Cooler Door Replacement Revision: 00 Models: Royal Vendors Coolers Tools required: Phillips screwdriver, 5/16" (8 mm) and 7/16" (12 mm) wrenches, ratchet with 7/16" (12 mm) socket Estimated time: 10 minutes Purpose: This Helpful Hint describes the procedure for replacing the door on a Royal Vendors Cooler. Download PDF: Helpful Hint 51 … [Read more...]
50. Proper Mounting Positioning for Various Changer Brands in non-CDC Venders
October 10, 2011 by ·
Subject: Proper Mounting Positioning for Various Changer Brands in non-CDC Venders Revision: 01 Models: Non-CDC Conventional Venders (GIII and Merlin IV) – Australia only Tools required: Phillips screwdriver Estimated time: <2 minutes Purpose: The changer door in Australian non-CDC conventional-style venders (i.e., GIII and Merlin IV) has been redesigned to more easily accomodate … [Read more...]
19. Optic Sensor Adjustment for 20 Plus Venders
September 12, 2011 by ·
Subject: Optic Sensor Adjustment for 20 Plus Venders Revision: 04 Models: 20 Plus Venders Tools required: Small flathead screwdriver Estimated time: 1 minute Purpose: To properly adjust the optic sensor when replacing a control board in a 20 Plus Vender. Download PDF: Helpful Hint 19 … [Read more...]
350. Extended Delivery Detector Cover Kit Installation
August 25, 2011 by ·
SUBJECT: Extended Delivery Detector Cover Kit Installation REVISION: 00 MODELS: RVV 500 ADA (Coca-Cola) PURPOSE: This bulletin describes the procedure for installing the extended delivery detector cover on the Coca-Cola RVV 500 ADA vender. This extended cover is designed to deflect water away from the detector board. Download PDF: Service Bulletin 350 … [Read more...]
348. RVV 500 Vertical Elevator Rail Replacement
August 3, 2011 by ·
SUBJECT: RVV 500 Vertical Elevator Rail Replacement REVISION: 00 MODELS: RVV 500 PURPOSE: Some defective vertical elevator rails were discovered which may rust prematurely. This rust does not affect function, but could be unsightly. This bulletin describes the most efficient procedure for replacing these rails. Download PDF: Service Bulletin 348 … [Read more...]
