SUBJECT: RVV X-axis Home Switch Cover Interference REVISION: 00 MODELS: RVV 400 PURPOSE: A limited number of Royal Vision Venders prior to serial number 200511MAXXXXX may experience interference between the X-axis home switch cover and the profile gasket on the refrigeration door. This interference could cause the elevator cup to not find its X-axis home position. When this occurs, the … [Read more...]
257. Installation of the RVV Upgrade Kit (Model 400 only)
March 9, 2005 by ·
SUBJECT: Installation of the RVV Upgrade Kit REVISION: 01 MODELS: RVV 400 PURPOSE: Original versions of the Royal Vision Vender (RVV) do not include some items which are now standard. This bulletin describes the procedure for updating this older equipment. Download PDF: Service Bulletin 257 … [Read more...]
32. Proper Depth Setting on Milk Venders
February 10, 2005 by ·
Subject: Proper Depth Setting on Milk Venders Revision: 00 Models: Milk Merchandiser Tools required: None Estimated time: <1 minute Purpose: Proper depth setting on Milk venders is essential, especially for selections vending bottles from rear columns. When set incorrectly, the vend motors in rear columns may not turn far enough for the bottle to drop from the column, resulting in a … [Read more...]
261. Installation of the RVV Override Key Switch Kit (Model 400 only)
February 10, 2005 by ·
SUBJECT: Installation of the RVV Override Key Switch Kit REVISION: 00 MODELS: RVV 400 PURPOSE: This bulletin explains the procedure for installing an override key switch kit in the RVV 400. Download PDF: Service Bulletin 261 … [Read more...]
260. Faulty Magnets in GIII Vend Chains
November 19, 2004 by ·
SUBJECT: Faulty Magnets in GIII Vend Chains REVISION: 00 MODELS: GIII PURPOSE: Some GIII vend chains produced for service parts were found in the field to have faulty magnets. NOTE: This bulletin only concerns vend chains produced for service parts, not the original chains installed in the venders at the factory. Download PDF: Service Bulletin 260 … [Read more...]
259. Override Switch Kit for the HVV Controller
November 8, 2004 by ·
SUBJECT: Override Switch Kit for the HVV Controller REVISION: 00 MODELS: HVV PURPOSE: This bulletin explains the procedure for installing an override switch kit in the HVV. Download PDF: Service Bulletin 259 … [Read more...]
254. Wall Spacer Kit Installation
October 4, 2004 by ·
SUBJECT: Wall Spacer Kit Installation REVISION: 00 MODELS: RVV (Serial number 200441MA00001 and after) PURPOSE: The Wall Spacer Kit was designed to prevent the RVV from being pushed all the way against a wall, allowing for air flow to the rear of the refrigeration area. Without air circulation in this area, the vender’s refrigeration unit cannot work properly. Download PDF: Service … [Read more...]
255. RVV Software Upgrade Kit Installation (Model 400 only)
September 1, 2004 by ·
SUBJECT: RVV Software Upgrade Kit Installation (Model 400 only) REVISION: 01 MODELS: RVV (control boards lower than 4.268 software revision) PURPOSE: When upgrading the software on RVV control boards with software revisions lower than 4.268, it is necessary to not only change the controller chip on the control board, but also to move the product sensing switch. This bulletin describes the … [Read more...]
252. Installing the Shorter T-handle Stud
July 6, 2004 by ·
SUBJECT: Installing the Shorter T-handle Stud REVISION: 00 MODELS: RVV PURPOSE: The Shorter T-handle Stud was designed for installation in Royal Vision Venders (RVV) before serial number 200419MA00001 to lessen the number of turns needed to completely shut and seal the door. This bulletin explains the proper procedure for installing this stud. Download PDF: Service Bulletin 252 … [Read more...]
253. Replacing the Glass Panel
July 6, 2004 by ·
SUBJECT: Replacing the Glass Panel REVISION: 00 MODELS: RVV PURPOSE: This bulletin describes the proper procedure for replacing the glass panel on the Royal Vision Vender (RVV). Download PDF: Service Bulletin 253 … [Read more...]
