Subject: GIII Controller Chute Sensor Adjustment Revision: 00 Models: All GIII / GIII Plus models Tools required: Flat screwdriver Estimated time: <2 minutes Information: This document describes the correct procedure for adjusting the sensitivity of the chute sensor on venders with GIII controllers. Download PDF: Helpful Hint 78 … [Read more...]
399. Reinforced T-handle Lock Cylinder Cover Kit Installation
May 21, 2015 by ·
SUBJECT: Reinforced T-handle Lock Cylinder Cover Kit Installation REVISION: 00 MODELS: All ADA venders and GIII Marketing PURPOSE OF THIS BULLETIN: The reinforced T-handle lock cylinder cover blocks off the T-handle to prevent access to the latch cylinder by vandals. Download PDF: Service Bulletin 399 … [Read more...]
76. GIII Vend Motor Troubleshooting Procedure
March 27, 2015 by ·
Subject: GIII Vend Motor Troubleshooting Procedure Revision: 00 Models: All GIII venders Tools required: Voltmeter Estimated time: N/A Information: This document describes the procedure for troubleshooting problems related to the vend motor on GIII venders. Download PDF: Helpful Hint 76 … [Read more...]
73. GIII Home Sensor Troubleshooting Procedure
March 13, 2015 by ·
Subject: GIII Home Sensor Troubleshooting Procedure Revision: 00 Models: All GIII venders Tools required: N/A Estimated time: N/A Information: This document describes the procedure for troubleshooting problems related to the home sensor on GIII venders. Download PDF: Helpful Hint 73 … [Read more...]
72. GIII Vend Chain Troubleshooting Procedure
February 6, 2015 by ·
Subject: GIII Vend Chain Troubleshooting Procedure Revision: 00 Models: All GIII venders Tools required: N/A Estimated time: N/A Information: This document describes the procedure for troubleshooting problems related to the chain assembly on GIII venders. Download PDF: Helpful Hint 72 … [Read more...]
395. LED Conversion Kit Installation in GIII Plus Venders
February 2, 2015 by ·
SUBJECT: LED Conversion Kit Installation in GIII Plus Venders REVISION: 03 MODELS: GIII Plus INTRODUCTION: This bulletin explains the procedure for converting GIII Plus venders built with T8 fluorescent lighting to a newer 24-volt LED lighting system. Download PDF: Service Bulletin 395 … [Read more...]
391. Clear Board Cover Installation on GIII Venders
December 3, 2014 by ·
SUBJECT: Clear Board Cover Installation on GIII Venders REVISION: 00 MODELS: GIII, GIII Plus BACKGROUND: A new clear board cover has been designed for use in GIII and GIII Plus venders to replace the black Kydex® cover that was previously used. Download PDF: Service Bulletin 391 … [Read more...]
392. GIII Control Board Troubleshooting
August 19, 2014 by ·
SUBJECT: GIII Control Board Troubleshooting REVISION: 00 MODELS: All GIII models BACKGROUND: This job aid guides you through the steps to troubleshoot a vender's main controller board, including power supply, refrigeration, chute sensor, multi-drop bus (MDB), etc. Download PDF: Service Bulletin 392 … [Read more...]
388. Coin Slot Hole Blocker Installation
April 24, 2014 by ·
SUBJECT: Coin Slot Hole Blocker Installation REVISION: 01 MODELS: CCIV, GIII Plus, RVV 500 (non-ADA) PURPOSE: This bulletin explains the procedure for installing the coin slot hole blocker, which prevents customers from inserting coins in venders with whole-dollar sales prices or card-only sales. Download PDF: Service Bulletin 388 … [Read more...]
80. Installation of Changer Jacket
April 2, 2014 by ·
SUBJECT: Installation of Changer Jacket REVISION: 03 MODELS: All venders PURPOSE: This bulletin explains the procedure for installing a rubber jacket around the top section of the changer. Download PDF: Service Bulletin 80 … [Read more...]
