SUBJECT: Installation of the Chute Sensor Adaptor REVISION: 03 MODELS: GII Venders (serial numbers 1300-0000 and before) PURPOSE: This bulletin explains the procedure for installing an adapter for using the newer adjustable chute sensor with the GII control board. Download PDF: Service Bulletin 118 … [Read more...]
Archive: Documentation
2. Fluorescent Bulb Removal (GIII Marketing)
June 18, 2002 by ·
Subject: Flavor Card Removal from the Select Button Revision: 03 Models: GIII Marketing Venders Tools required: None Estimated time: 2 minutes Purpose: To show the correct way to remove a fluorescent bulb from a marketing vender. Download PDF: Helpful Hint 2 … [Read more...]
18. Ground Strap for the Inner Door
June 18, 2002 by ·
Subject: Ground Strap for the Inner Door Revision: 03 Models: All Venders Tools required: Phillips screwdriver, drill, 1/8” drill bit Estimated time: 1 minute Purpose: For instructions on installing a ground strap to the inner door. Download PDF: Helpful Hint 18 … [Read more...]
21. GIII Energy Conservation
June 18, 2002 by ·
Subject: GIII Energy Conservation Revision: 02 Models: GIII Tools required: N/A Estimated time: N/A Purpose: To conserve energy and utilize features the GIII provides to reduce your costs. Download PDF: Helpful Hint 21 … [Read more...]
22. Fluorescent Bulb Removal Instructions for Low Overhead Clearance
June 18, 2002 by ·
Subject: Fluorescent Bulb Removal Instructions for Low Overhead Clearance Revision: 03 Models: MIV CDC Tools required: Phillips screwdriver, 11/32” socket Estimated time: 10 minutes Purpose: To show the proper way to remove a fluorescent bulb from a MIV CDC vender when it is situated with a low overhead clearance. Normally the bulbs could be carefully lifted out between the changer vault … [Read more...]
23. MIV Energy Conservation
June 18, 2002 by ·
Subject: MIV Energy Conservation Revision: 02 Models: Merlin IV Tools required: N/A Estimated time: N/A Purpose: Utilize features the MIV provides to reduce your costs and conserve energy. Download PDF: Helpful Hint 23 … [Read more...]
24. Door Removal with the Universal (Wrap Around) Hinge
June 18, 2002 by ·
Subject: Door Removal with the Universal (Wrap Around) Hinge Revision: 03 Models: MIV, GIII Tools required: Adjustable wrench, 3/8” wrench, 1/4” socket, 9/16” deep-well socket Estimated time: 20 minutes Purpose: Venders produced after 2000 34XX-XXXXX have a different top hinge, which was designed for anti-vandal reasons. This Helpful Hint was created to give directions how to remove the … [Read more...]
16. Installation of Validator (deeper than 4 1/2”)
June 18, 2002 by ·
Subject: Installation of Validator (deeper than 4 1/2”) Revision: 03 Models: Landscape venders Tools required: Drill, 1/8” drill bit, 11/32” deep-well socket Estimated time: 5 minutes Purpose: This document describes the procedure for installing a validator deeper than 4 1/2". Download PDF: Helpful Hint 16 … [Read more...]
12. GII Conversion to GIII EVS Software (using parts currently in the vender)
June 18, 2002 by ·
Subject: GII Conversion to GIII EVS Software Revision: 04 Models: GII Tools required: Small flathead screwdriver (to adjust chute sensor) Estimated time: 20 minutes Purpose: This document describes the procedure for installing a GIII control board in a GII vender. Download PDF: Helpful Hint 12 … [Read more...]
11. Replacing a Vend Motor (MIV)
June 18, 2002 by ·
Subject: Replacing a Vend Motor (MIV) Revision: 03 Models: Merlin IV venders Tools required: Phillips screwdriver; may also need a drill and 3/8” drill bit Estimated time: 15 minutes Purpose: This document describes the procedure for replacing a vend motor in the Merlin IV vender. Download PDF: Helpful Hint 11 … [Read more...]
