SUBJECT: T12 to Low-power LED Conversion Kit Installation REVISION: 00 MODELS: All 20+ (TDV) venders PURPOSE: 20+ (TDV) Venders have two different vend motors installed: a low-torque motor, for all front columns; and a high-torque motor, for all rear columns. These two motor types are NOT interchangeable. Download PDF: Service Bulletin 284 … [Read more...]
282. RVV NG Changer Guard Kit Installation
March 14, 2007 by ·
SUBJECT: RVV NG Changer Guard Kit Installation REVISION: 00 MODELS: RVV NG with T-handle Lock PURPOSE: This bulletin describes the proper procedure for installing the Changer Guard Kit, which provides protection from vandalism for the changer in the RVV NG. Download PDF: Service Bulletin 282 … [Read more...]
283. GFCI Main Wiring Harness Implementation
March 13, 2007 by ·
SUBJECT: GFCI Main Wiring Harness Implementation REVISION: 00 MODELS: All venders built for use in the USA (including Puerto Rico) and Canada PURPOSE: Effective April 2007, all new venders are required to have a GFCI (Ground Fault Circuit Interrupter) built into the main wiring harness coming from the power source (wall outlet). This change has been legally mandated by Underwriters … [Read more...]
42. 220-240 VAC Electronic Ballast Replacement
January 30, 2007 by ·
Subject: 220-240 VAC Electronic Ballast Replacement Revision: 00 Models: RVV NG, Merlin RB (230 VAC 50 Hz models only) Tools required: Phillips screwdriver Estimated time: 5 minutes Purpose: The seven-connector 220-240 volt electronic ballast that was originally used in the international RVV NG and Merlin RB venders has been replaced by a newer four-connector electronic ballast. This … [Read more...]
271. Merlin RB Lock Cover Kit Installation
January 16, 2007 by ·
SUBJECT: Merlin RB Lock Cover Kit Installation REVISION: 01 MODELS: Merlin RB PURPOSE: This bulletin describes the correct procedure for installing the Merlin RB Lock Cover Kit, which prevents vandals from drilling into the T-handle lock cylinder. Download PDF: Service Bulletin 271 … [Read more...]
249. Installation of the RVV Lock Cover Kit
January 16, 2007 by ·
SUBJECT: Installation of the RVV Lock Cover Kit REVISION: 02 MODELS: RVV, RVV NG, RVV Gen II PURPOSE: Installing a lock cover helps to prevent vandalism and deter theft. This bulletin describes the proper procedure for installing a lock cover kit on the RVV and the RVV NG. Download PDF: Service Bulletin 249 … [Read more...]
281. Installation of the Bottom Door Stop Kit
January 9, 2007 by ·
SUBJECT: Installation of the Bottom Door Stop Kit REVISION: 00 MODELS: RVV NG KO (except Australia) PURPOSE: The bottom door stop was designed as a replacement for the top door stop, which could damage vender fascia. The door stop allows the vender's door to open only a certain distance so that the vender's harnessing is not overstretched. Download PDF: Service Bulletin 281 … [Read more...]
256. Installation of the Hall Effect Sensor (Model 400 only)
October 3, 2006 by ·
SUBJECT: Installation of the Hall Effect Sensor REVISION: 02 MODELS: RVV PURPOSE: Beginning with serial number 200424MA00001, all model 400 Royal Vision Venders (RVV) have a Hall Effect sensor for detection of product in the elevator cup, instead of the microswitch used on older RVVs. This bulletin describes the proper procedure for converting from the older microswitch to the Hall Effect … [Read more...]
279. Incorrect Refrigerant Charge on Vender Serial Plate
September 26, 2006 by ·
SUBJECT: Incorrect Refrigerant Charge on Vender Serial Plate REVISION: 00 MODELS: Australian RVV NG PURPOSE: On the vender serial plates of some RVV NGs built for export to Australia, the refrigerant charge quantity is listed incorrectly. On these units, the charge is listed as “0.17 kg” instead of the correct charge, 0.23 kg. Download PDF: Service Bulletin 279 … [Read more...]
278. RVV NG IEC Wiring / Label Checklist
September 21, 2006 by ·
SUBJECT: RVV NG IEC Wiring / Label Checklist REVISION: 00 MODELS: RVV NG 230 VAC 50 Hz models PURPOSE: This bulletin is provided as a checklist for the placements of decals, etc., provided as safety measures on all 230 VAC 50 Hz models of the RVV NG, as shown in the following pictures. Download PDF: Service Bulletin 278 … [Read more...]
