SUBJECT: Lamp Relay Kit Installation REVISION: 09 MODELS: GIII, Merlin III, Merlin IV, HVV, and TDV venders PURPOSE: This bulletin shows the correct procedure for installing the lamp relay kit, which allows the controller to turn the lighting system on or off. Download PDF: Service Bulletin 113 … [Read more...]
51. Cooler Door Replacement
October 20, 2011 by ·
Subject: Cooler Door Replacement Revision: 00 Models: Royal Vendors Coolers Tools required: Phillips screwdriver, 5/16" (8 mm) and 7/16" (12 mm) wrenches, ratchet with 7/16" (12 mm) socket Estimated time: 10 minutes Purpose: This Helpful Hint describes the procedure for replacing the door on a Royal Vendors Cooler. Download PDF: Helpful Hint 51 … [Read more...]
50. Proper Mounting Positioning for Various Changer Brands in non-CDC Venders
October 10, 2011 by ·
Subject: Proper Mounting Positioning for Various Changer Brands in non-CDC Venders Revision: 01 Models: Non-CDC Conventional Venders (GIII and Merlin IV) – Australia only Tools required: Phillips screwdriver Estimated time: <2 minutes Purpose: The changer door in Australian non-CDC conventional-style venders (i.e., GIII and Merlin IV) has been redesigned to more easily accomodate … [Read more...]
19. Optic Sensor Adjustment for 20 Plus Venders
September 12, 2011 by ·
Subject: Optic Sensor Adjustment for 20 Plus Venders Revision: 04 Models: 20 Plus Venders Tools required: Small flathead screwdriver Estimated time: 1 minute Purpose: To properly adjust the optic sensor when replacing a control board in a 20 Plus Vender. Download PDF: Helpful Hint 19 … [Read more...]
350. Extended Delivery Detector Cover Kit Installation
August 25, 2011 by ·
SUBJECT: Extended Delivery Detector Cover Kit Installation REVISION: 00 MODELS: RVV 500 ADA (Coca-Cola) PURPOSE: This bulletin describes the procedure for installing the extended delivery detector cover on the Coca-Cola RVV 500 ADA vender. This extended cover is designed to deflect water away from the detector board. Download PDF: Service Bulletin 350 … [Read more...]
348. RVV 500 Vertical Elevator Rail Replacement
August 3, 2011 by ·
SUBJECT: RVV 500 Vertical Elevator Rail Replacement REVISION: 00 MODELS: RVV 500 PURPOSE: Some defective vertical elevator rails were discovered which may rust prematurely. This rust does not affect function, but could be unsightly. This bulletin describes the most efficient procedure for replacing these rails. Download PDF: Service Bulletin 348 … [Read more...]
331. EMS Motion Sensor Installation
August 3, 2011 by ·
SUBJECT: EMS Motion Sensor Installation REVISION: 01 MODELS: GIII with EMS Software PURPOSE: Beginning with serial week 201135, all new GIII venders (804, 660, and 550 models) will be manufactured with the Energy Management System (EMS) installed. Venders built before 201135 may be retrofitted with EMS. This bulletin explains the procedure for installing the motion sensor for use with the … [Read more...]
48. Recommendations to Enhance Package Vending Reliability
June 21, 2011 by ·
Subject: Recommendations to Enhance Package Vending Reliability Revision: 01 Models: 804, 660, 550 Tools required: N/A Estimated time: N/A Purpose: Bottle bridging can have various causes. This Helpful Hint bulletin describes how to enhance vending reliability in a GIII-style machine. Download PDF: Helpful Hint 48 … [Read more...]
344. RVV Cleaning
May 24, 2011 by ·
SUBJECT: RVV Cleaning REVISION: 00 MODELS: RVV 500 PURPOSE: In some RVV 500 venders, a white powdery substance has been found. Tests have shown this powder to be hydrated aluminium oxide and magnesium chlorate, both non-hazardous materials. This bulletin explains the procedure for cleaning the venders in which this powder is present. Download PDF: Service Bulletin 344 … [Read more...]
343. Reorientation of Metal Evaporator Fan Motor
March 31, 2011 by ·
SUBJECT: Reorientation of Metal Evaporator Fan Motor REVISION: 01 MODELS: RVV 500 PURPOSE: In some RVV 500 venders built from September 2010 until March 2011, moisture from condensation could get inside the evaporator fan motors through the opening for the power cord. Beginning in March 2011, the orientation of the fan motors in the vender was changed to prevent this moisture from getting … [Read more...]
