SUBJECT: Wall Spacer Kit Installation REVISION: 00 MODELS: RVV (Serial number 200441MA00001 and after) PURPOSE: The Wall Spacer Kit was designed to prevent the RVV from being pushed all the way against a wall, allowing for air flow to the rear of the refrigeration area. Without air circulation in this area, the vender’s refrigeration unit cannot work properly. Download PDF: Service … [Read more...]
Archive: Service Bulletins
255. RVV Software Upgrade Kit Installation (Model 400 only)
September 1, 2004 by ·
SUBJECT: RVV Software Upgrade Kit Installation (Model 400 only) REVISION: 01 MODELS: RVV (control boards lower than 4.268 software revision) PURPOSE: When upgrading the software on RVV control boards with software revisions lower than 4.268, it is necessary to not only change the controller chip on the control board, but also to move the product sensing switch. This bulletin describes the … [Read more...]
252. Installing the Shorter T-handle Stud
July 6, 2004 by ·
SUBJECT: Installing the Shorter T-handle Stud REVISION: 00 MODELS: RVV PURPOSE: The Shorter T-handle Stud was designed for installation in Royal Vision Venders (RVV) before serial number 200419MA00001 to lessen the number of turns needed to completely shut and seal the door. This bulletin explains the proper procedure for installing this stud. Download PDF: Service Bulletin 252 … [Read more...]
253. Replacing the Glass Panel
July 6, 2004 by ·
SUBJECT: Replacing the Glass Panel REVISION: 00 MODELS: RVV PURPOSE: This bulletin describes the proper procedure for replacing the glass panel on the Royal Vision Vender (RVV). Download PDF: Service Bulletin 253 … [Read more...]
251. Installation of the Merlin Packaging Kit
July 5, 2004 by ·
SUBJECT: Installation of the Merlin Packaging Kit REVISION: 00 MODELS: Merlin IV, Milk PURPOSE: Before shipping and storing the Merlin venders, the Merlin Packaging Kit should be installed to prevent damage to the venders. Download PDF: Service Bulletin 251 … [Read more...]
248. Installation of the RVV Milk Conversion Kit (Model 400 only)
April 20, 2004 by ·
SUBJECT: Installation of the RVV Milk Conversion Kit REVISION: 00 MODELS: RVV (Model 400 only) PURPOSE: Before loading perishable items in the Royal Vision Vender (RVV), a health safety sensor must be installed and enabled. This bulletin describes the proper procedure for installing the RVV Milk Conversion Kit, which includes this health safety sensor. Download PDF: Service Bulletin 248 … [Read more...]
246. Port Shield Installation
March 10, 2004 by ·
SUBJECT: Port Shield Installation REVISION: 00 MODELS: All CCR models PURPOSE: The CCR port shield is designed to prevent vandalism by adding reinforcement to the vender’s port panel. This bulletin describes the proper installation procedure for this part. Download PDF: Service Bulletin 246 … [Read more...]
245. Merlin Electrical Noise Filter Kit Installation
January 30, 2004 by ·
SUBJECT: Merlin Electrical Noise Filter Kit Installation REVISION: 00 MODELS: Merlin IV, Milk Merchandiser, and EZ Vender with Multi-Layer control board PURPOSE: Due to electromagnetic noise, on some Merlin IV, Milk Merchandiser, and EZ Venders with Multi-Layer control boards it may appear difficult or impossible to adjust the delivery chute sensor’s sensitivity. These boards also may have a … [Read more...]
233. Retrofitting Coke Venders with T8 Lighting
January 23, 2004 by ·
SUBJECT: Retrofitting Coke Venders with T8 Lighting REVISION: 02 MODELS: All venders with Coke-style doors (115 VAC only) PURPOSE: This bulletin explains the procedure for upgrading the old-style T12 lighting system to the newer, more energy-efficient T8 lighting system. Download PDF: Service Bulletin 233 … [Read more...]
243. Version 41.xx Chip Replacement
November 12, 2003 by ·
SUBJECT: Version 41.xx Chip Replacement REVISION: 00 MODELS: Merlin IV with Versatile Control Board (Revision 41.xx) PURPOSE: This bulletin shows the correct procedure for replacing the Merlin IV Rev. 41.XX (Versatile control board) EEPROM chip. Download PDF: Service Bulletin 243 … [Read more...]
