SUBJECT: Coin Deflector Kit Installation REVISION: 00 MODELS: GIII venders with Center Door Changer PURPOSE OF THIS BULLETIN: This bulletin describes the procedure for installing the coin deflector kit in GIII venders with Center Door Changers. Download PDF: Service Bulletin 401 … [Read more...]
Archive: Service Bulletins
399. Reinforced T-handle Lock Cylinder Cover Kit Installation
SUBJECT: Reinforced T-handle Lock Cylinder Cover Kit Installation REVISION: 00 MODELS: All ADA venders and GIII Marketing PURPOSE OF THIS BULLETIN: The reinforced T-handle lock cylinder cover blocks off the T-handle to prevent access to the latch cylinder by vandals. Download PDF: Service Bulletin 399 … [Read more...]
398. 20 oz Anti-bridging Kit for Merlin IV
SUBJECT: 20 oz Anti-bridging Kit for Merlin IV REVISION: 00 MODELS: 72" Merlin IV (models 650 and 542) PURPOSE OF THIS BULLETIN: In certain vintages of Merlin IV venders, bridging may occur with some 20 ounce bottles. In the event this occurs, this anti-bridging kit should alleviate the issue. Download PDF: Service Bulletin 398 … [Read more...]
397. Optimized Placement of Bimetal Switch
SUBJECT: Optimized Placement of Bimetal Switch REVISION: 02 MODELS: Freezer PURPOSE OF THIS BULLETIN: On Royal Vendors Freezers with serial numbers 201518RA00054 and before, the bimetal switch in the refrigeration assembly was placed on the 1/4" line going into the expansion valve, which may not allow the cabinet to pull down to the correct temperature. This bulletin explains the procedure … [Read more...]
396. Enabling the Battery on the Health Timer Freezer Controller
SUBJECT: Enabling the Battery on the Health Timer Freezer Controller REVISION: 00 MODELS: Health Safety Freezer REASON FOR BULLETIN: The Health Safety Freezer Controller's backup battery is disabled when not installed in the Freezer to preserve its shelf life. Failure to enable the battery will cause the door lock mechanism to stay in the locked position in the event the Freezer loses … [Read more...]
395. LED Conversion Kit Installation in GIII Plus Venders
SUBJECT: LED Conversion Kit Installation in GIII Plus Venders REVISION: 03 MODELS: GIII Plus INTRODUCTION: This bulletin explains the procedure for converting GIII Plus venders built with T8 fluorescent lighting to a newer 24-volt LED lighting system. Download PDF: Service Bulletin 395 … [Read more...]
391. Clear Board Cover Installation on GIII Venders
SUBJECT: Clear Board Cover Installation on GIII Venders REVISION: 00 MODELS: GIII, GIII Plus BACKGROUND: A new clear board cover has been designed for use in GIII and GIII Plus venders to replace the black Kydex® cover that was previously used. Download PDF: Service Bulletin 391 … [Read more...]
394. Vend Motor Harness Clip Installation
SUBJECT: Vend Motor Harness Clip Installation REVISION: 00 MODELS: KO Merlin BACKGROUND: Some KO Merlin venders were produced without P-clips to secure the vend motor harness. On these venders, it is possible for the product chute to scrape the harness, which can cut through the outer insulation of the harness over time and cause it to fail. This bulletin explains the procedure for … [Read more...]
393. Left-hand Cooler Door Hinge Installation
SUBJECT: Left-hand Cooler Door Hinge Installation REVISION: 00 MODELS: All Cooler models INFORMATION: This bulletin describes the procedure for changing the hinge from the right side to the left side on a Royal Vendors Cooler. Download PDF: Service Bulletin 393 … [Read more...]
392. GIII Control Board Troubleshooting
SUBJECT: GIII Control Board Troubleshooting REVISION: 00 MODELS: All GIII models BACKGROUND: This job aid guides you through the steps to troubleshoot a vender's main controller board, including power supply, refrigeration, chute sensor, multi-drop bus (MDB), etc. Download PDF: Service Bulletin 392 … [Read more...]
